I love my Switch. I got a V3 so when I want to do immersion, I can play with bigger volumes. I have a V2 glass V60 as well, and can swap that onto the switch if needed.

This is such a great write-up. Thank you!

Any craft store will have tiny rubber and nylon hammers for jewelry and crafts. Small Rubber and nylon mallet

I really like James Hoffmann’s French Press technique: Hoffmann’s Ultimate French Press

Yeah, I think you can buy the Oxo carafe separately if you want an extra, but I haven’t looked into it. We transfer the brew concentrate into taller carafes so they don’t take up as much space in our fridge (I think they’re the 1L Anchor Hocking carafes with lids).

By the time we are pouring the last bit of the concentrate, the small amount of sludge stays in the carafe and doesn’t impact the cup!

Oh I forgot about the paper filters for the Oxo! I think you’re right about the slight difference in size. I stopped using the paper filters and only use the mesh screen, as I still enjoy the brews without them.

Nice and thoughtful post about cold brew and the Toddy! I did Toddy batches weekly for a couple years and enjoyed the smoothness and convenience you described. I had to purchase another container because of the dreaded crack near the stopper. Eventually I switched to the Oxo and haven’t looked back. Benefits are: no need to mess with sponge filters, no reaching under to pull out the stopper, looks great on the countertop, self-contained and packs up nicely for storage.

Same price range as the Toddy, so keep it in mind if your Toddy ever cracks. Happy brewing!

30g coffee to 480g water, 96 C, 03 Switch

• 0:00 add 60g bloom w switch open
• 0:45 add 140g w switch open (total 200g)
• 1:30 close switch add 280g immersion (total 480g)
• 2:30 open switch Finish around 3:20

Ahhh great! You’re starting to slide already! A pour over is my daily driver and my preferred method for light roasts. If you go this route you will additionally need a scale and will greatly benefit from a gooseneck kettle.

Folx have some great comments above. Personally, I think a plastic V60 is a great starting point to refine your technique without having to worry about the thermal impact of glass or porcelain on your slurry. A clever dripper is a good option too.

Also a good hand grinder (eg: 1zpresso) makes a world of difference for pour overs!

Oh man there are so many starting points! If I understand the goals you gave us, they are:

• Want good coffee
• No pour over
• Willing to do French Press
• Minimize grounds in the brew
• Single serve
• Brother-in-law is too intense about it for my current state

With that I would recommend an AeroPress. It is great for single serving, it extracts using immersion first (similar to French Press) then pressure, the paper filter ensures it will be a clean cup (no grounds), it is much easier to clean up than a French Press, and there a lot of different recipes to play with should you ever choose to. Plus it’s relatively cheap.

Cold brew is also nice, especially when made in batches. You can probably already do this with vessels you have at home. Toddy cold brew is a well-known system. I also have (and prefer) the Oxo cold brew system - I find it easier to handle and looks better on the counter.

If you are willing to get a burr grinder you will immediately make better coffee, regardless of the method you choose! There are many directions to go here, so you will need to research to find what makes most sense to you. Skip the blade grinder. Conical burr is fine for what you’re getting into. A safe bet that will work fine for French Press, AeroPress, and/or Cold Brew is the Oxo Brew Conical Burr Grinder that you can find for around $100 in the US.

There are so many deep rabbit holes from there. Maybe you’ll come join us someday…it’s a lot of fun and one of my favorite hobbies! Sounds like your brother-in-law is lost somewhere down here too. We all started asking the same questions as you!

Just pulled an espresso blend (Brazil, Guatemala, Honduras; washed and natural) on my Cafelat Robot.

Thanks for this! Will start slow feeding and see how it changes.

Based on the theory here, slow feeding doesn’t make the grounds finer, but actually overall coarser by reducing fines on the same grinder setting. So although you are adjusting to a lower number (finer setting) on your grinder, the actual particles are not finer, but more uniformly distributed. Bottom line: you should definitely try this for your pour overs!

I agree! I love my 1zpresso K-Max and use it daily for pour over (V60, Orea V3) and use it for espresso (Cafelat Robot) when we go camping.

In a world full of grey, there’s only one answer to this one: Lafayette!

Agreed! That and black are my favorites.

Acme? Love that blue!

Sounds like you’re enjoying it! I haven’t started the series yet but read the book and highly recommend it.

I bought a few Fellow Carter Move mugs in the last 6 months and have no problems with smell. I prefer the ceramic coating inside to the stainless steel of the Zojuroshi, and they’re easier to clean.

I prefer the glass versions to ceramic, as ceramic really sucks the heat out of the slurry. Hario has a beautiful glass v60. Also I have the new glass Orea V3 flat bottom brewer.

Thanks for posting this! It inspired me to pull out my phin filters and some robusta beans and brew cà phê sữa nóng in place of our typical v60 pour over today. I need to have a go at cà phê trứng at some point - haven’t made that at home yet.